Mesa Tactical Forum

Here's my work 870P with 6-shot SureShell Carrier and Enidine Recoil Reducer/M4 Stock. Note the action has already cycled and is back on target while empty hull is barely below arm-level. The recoil reducer works very well indeed.

Here is my M4 with its Mesa gear.

Rem 870HD. No practical use what so ever. Just a fun build. Now if I could only decide on a red dot.





*edit: finally got the red dot!

Last edited by emrivera1 (2008-10-09 18:55:34)

I know the pic is bad, I'll post some better from my next shoot. (This is from a cell phone)
Here's my Winchester 1300 Defender, Vera. I fear she will always be a work in progress.

-Endine Shot Shock Recoil Buffer
-Magpul CTR
-ACE Ltd. Side Folding adapter
-One Shot Tactical 1913 rail (Clamp slightly modified for Winchester barrel)
-AR carry handle/flip up front sight

The Surefire weaponlight is attached via the bottom rail setup from my M14 SOCOM II, a temporary use, just testing it out.

Currently saving up for a Surefire Pump, and an eOtech 553.

Hey, Vicious, a couple questions.......

What type of shotgun is that?  Is that a mesa high tube adapter?  I'm looking at putting a Ace Ltd UL-M stock on an 870 and your shotgun looks very similar to what I was thinking.  Just wanted to find out if there was anything special that needed to be done other then putting the adapter on the gun and the stock on the adapter.

Sage M870 with mesa rail

I love you guys!

KISS....

Remington 870 Marine Magnum

- Cavalry Arms SST-870 Stock Adapter
- Surefire 618 LFG Forend
- Magpul CTR
- Magpul MIAD
- Magpul ASAP
- Mesa Tactical 6 Shot Shell Carrier
- Mesa Tactical 4 Shot Shell Carrier
- Mesa Tactical Magazine Clamp/Swivel
- Mesa Tactical/Enidine Hydraulic Recoil Buffer Tube

tried my best to wait out for the Mesa High Tube Adapter but couldn't wait any longer, will definitely be getting one sooner or later for another 870 though

Here is a pic of my duty shotgun. It started out as a "stock" Scatterguns Technology 870 w/ 14" barrel. (Back when Scattergun was based out of Nashville before being sold to Wilson)

After I got my little paws on it I added a Surefire Lighted Fore-end, Mesa's Low Tube Adapter with the sight rail (which I believe was still in the prototype stage when it was sent to me). I slapped on a Trijicon Reflex II sight w/ Amber Triangle and used the dept issued side saddle. The only parts on the gun that belong to the city is the receiver, the barrel, and the side saddle....lol  shoots great too.

The only issues I have had was with the sight rail. Mine is one of the very early versions (if I remember correctly Mitch had told me it was originally been designed to work on the 870 and the Moss 500) and it sits too high off of the receiver (not a flush mount like the new ones). I had to get our Dept's gunsmith to mill out the center channel of the rail more so I could use the ghost ring sights under  the Trijicon base. I still need to mill out some more in order to get a proper sight picture, but it works so-so in an emergency.

Last edited by FLEXCopMNPD (2010-01-05 21:29:13)

Here's my 20" Mossberg 500-
MT Low Tube Adapter
Magpul MIAD
Magpul AFG
Magpul MOE
CAA Forend
Not pictured is the Enidine Buffer installed after this pic was taken



The pistol is a Sig Sauer SP2022 9mm w/ Streamlight TLR-3