Product Description
SureShell® Aluminum Carrier For Moss 500 (Side Mount)
Our SureShell shotshell carriers retain ammunition reliably and, being metal, can withstand the rigors of daily use and abuse. Fabricated from aircraft aluminum, they feature an innovative rubber friction retention system and tough construction to endure years of use and abuse. Since their introduction, they have rapidly become our bestselling accessories, and an emerging industry standard.
SureShell carrier yokes are milled from 6061-T6 aircraft aluminum, then bead blasted and Mil-spec hard anodized for a rugged non-glare finish. SureShell yokes are secured to application-specific brackets, and some SureShell carriers include high temperature adhesive-backed die-cut rubber gaskets to protect the host shotgun’s finish.
SureShell shotshell carriers are available in two configurations: four-shell and six-shell. The six-shell configurations can be installed on the left side of the receiver.
Mossberg
The side mount scheme of our shotgun SureShell shotshell carriers for the Mossberg 500/590 substitutes two custom-machined steel Chicago screws for the trigger pin. At the front of the mounting plate, custom retaining steel hardware is used with an elongated extractor screw and a machined key hole in the plate. The Mossberg 930 mounting system is similar, except it uses two sets of Chicago screws in place of the two trigger pins. The mounting plate was designed not to obscure the receiver serial number to make it easier for armorers to inventory their weapons. SureShell shotshell carriers for the Mossberg fit on the left side of the receiver only. You must use a tactical forend that does not significantly overlap the receiver, or a factory forend that is cut down appropriately. SureFire forends will work fine with no alterations.
- THE BEST AND MOST DURABLE WEAPON MOUNTED SHOTSHELL CARRIER AVAILABLE
- INNOVATIVE RUBBER FRICTION RETENTION SYSTEM SOLIDLY HOLDS SHOTSHELLS IN PLACE
- MACHINED FROM 6061-T6 ALUMINUM
- HARD COAT ANODIZED MATTE BLACK
- MOUNTS VIA BRACKETS ATTACHED TO SHOTGUN OR VIA DRILLED AND TAPPED RECEIVER HOLES
- MIL-SPEC HARD COAT ANODIZED FOR A RUGGED NON-GLARE FINISH
- MOST SURESHELL ALUMINUM SHOTSHELL CARRIERS MOUNT DIRECTLY TO A SPECIFIED RECEIVER
Other Details
WARRANTY All Mesa Tactical products are made in the USA of high quality materials and include LIFETIME WARRANTY. Mesa Tactical warrants that all products are free from defective material and workmanship and, subject to the conditions set forth below, agrees to repair or replace any part of a product that proves defective by reason of improper workmanship or materials without charge for parts and labor. In no event will Mesa Tactical be liable for damages, lost revenue, lost wages, lost savings or any other incidental or consequential damages arising from purchase, use or inability to use this product. No express or implied warranty is madefor Mesa Tactical product damaged by accidents, misuse, natural or personal disaster, or any unauthorized disassembly, repair or modification. Mesa Tactical’s warranty covers only repair or replacement of defective Mesa Tactical products. *No export license is required for most international destinations.Product Videos
Custom Field
Product Reviews
15 Reviews Hide Reviews Show Reviews
-
SureShell
Customer service with Mesa Tactical is exceptional. Product arrived and was easy to install. Will definitely do business with them again! Thank you.
-
Well Made
This is the second one of these I have purchased. The first was for a Remington 870 I had in my patrol car for 6 years. Hot or cold this shell carrier was great. At one point the shells got loose from the temperature extremes, I contacted Mesa, they sent some new tube inserts for free. I recommend these to everyone. Great product. Thanks guys.
-
Consistency
First of all it’s a well made product with good finish and good instructions. It’s a bit heavy but that’s too be expected buying this big of an aluminum attachment. I have 2 slight problems that keep this from being a perfect product and it would be the receiver screw and the elastomer. The bolt can get caught on the new receiver screw and just causes more friction when racking the gun, I can already see wear on top of the screw because it doesnt fit low enough and I have tightened it down as much as I can. The elastomer is very inconsistent, some sections fit way too tight and then the one right next to that one is just way too loose, it’s hard to train with because it switches around…wasn’t worth the $75 honestly
-
Sure Shell Aluminum Carrier for Mossberg 590
Works perfectly. Good machining and fit to my 590. Instructions are clearly written and I had it installed in 10 minutes. I recommend this product.
-
Solid Addition
Sturdy construction and easy install. The rubber holding the shells is super tight but I know its just breaking it in. I had the something similar on my Remington 870 from these guys and worked like a dream The reason I'm even writing this is the customer service. I had stripped a screw on my older one and when asked about new hardware for it they just sent it. I was blown away!! Stuff like that is how you get me coming back. It a little on the higher end in price but the life time support of their products makes it worth it. 2nd one I bought from them.
-
N/A
Can't give a review got sent the wrong part,
-
Exactly as ordered.
Fast shipment, easy installation, and a quality product. It's nigh-indistinguishable from an early production of the same item on another shotgun of mine; its that consistent over the years. Oh, and great customer service, too! There may be cheaper options out there, but Mesa has earned my repeat business through their product design, product quality and consistency, and their support for their wares, no matter when it was purchased (or by whom). You don't get what you pay for. You get more.
-
Great quality, easy installation.
Great quality, easy not cut/drill/weld installation. Made in USA. Looks awesome. Very useful for carrying 6 extra 12 ga shot shells. Installed on a Mossberg 590A1 Tactical Magpul Edition. Shell holder is a bit pricey but worth it. Comes well packaged and with plenty of clear instructions and all necessary backup hardware.
-
Mossberg 500 Sureshell (6-shell 12 GA)
I wasn"t sure if the product would fit with my Crimson Trace Laser. It fit perfectly. I just eliminated one washer. Well designed and manufactured. Should last forever. Appreciate the extra, spare, parts.